![]() ![]() “The word "biometric" simply means the measurement of a living trait, whether physiological or behavioral. The size and shape of a hand, a fingerprint, the voice and several aspects of the eye are just some unique attributes. Biometrics identifies people by a unique human characteristic. My employees are concerned about hygiene issues.What happens if I injure my hand and have it bandaged or in a cast?.How many hand templates can be stored in the unit?.All information can be added or changed at a later date with the If the PC Clock is installed, check the box to assign If the Benefit Accrual Module is installed, assign theĮmployee to an Accrual Rule. Assign the employee to a Division, GroupĪnd Holiday Group (if in use). Enter a unique employee number and the employee’s personal information.All the fields will be blank, with the Hire date and the Fiscal date set to the Current.Click the Add button at the bottom of the window to add a new employee.In the Configure Employee screen, press the Detail tab to change to the Employees.This will open the Configure Employee Screen. To add an employee, click on the Employee icon, or select Daily Operations, thenĮmployee.TA100 Pro/Genesis Pro Help: Add New Employee To Software Press: Dispelling The Myths About Biometrics.Press: How Automation Reduces Your Payroll Costs.Press: Nucleus Research Paper on Biometric HandPunch.Your HandPunch Time should now be correct.Make sure your computer time is correct.Verify/Enter Gateway (make sure to use all 3 numbers in each octet).Verify/Enter IP Address (make sure to use all 3 numbers in each octet).Enter your Supervisor ID, followed by the Enter key: XXX then Enter.To get entry to password level Press: Clear and Enter.Enter new supervisor ID, followed by the "Enter" key.To get entry to menus, press: "Clear" and "Enter".Enter the Employee ID, followed by the "Enter" key.Enter your supervisor ID, followed by the "Enter" key (if prompted).To get entry to password level Press: "Clear" and "Enter".Rear corners of the platen and work your way forward.ĭO NOT SPRAY CLEANING FLUID DIRECTLY INTO OR ON THE HANDPUNCH. The platen, side mirror, reflector, and the window above the platen using a clean clothĭampened with ordinary, non-abrasive window cleaner (see Figure 8-1). Inspect and clean the HandPunch regularly to maintain optimum performance. If problems persists, contact us at (718) 784-4900 to get a loan unit from us.Check calibration scores once again at the clock (Write them down & compare).Let it restart, thenselect option "Cold Boot." ![]() Reset clock and perform a cold boot (Unplug power cord from clock and plug it back in, all while holding down the little white button in back of clock).Clean the clock with Windex (platen, side mirrors & under nose of clock/black plexiglass where the camera takes picture through) – all external parts.Check calibration scores at the clock.Poll clock one last time to get all punches in clock currently downloaded to Time and Attendance software.Simple Troubleshooting Guidelines if HandPunch is Not Working: However you can change it by going to Menu> System Settings> Security> Alarm> Rejection Alarm ON - there is a rejection time (meaning you can set it to 1-3, for the attempts for the alarm to go off). Q: What happens if someone not enrolled tries to punch at SY-910 face recognition clock ? Any noise or anything displayed on screen or does it just time out ?Ī: First time you attempt to punch and not enrolled it will time out by default. I know they are talking to the developer to attempt to get them sent from the software. Q: Can SY-910 Face Recognition Unit ring bells ?Ī: Yes, but programmed at clock directly via keypad ! Q: If someone tries to punch in twice within 5 minutes what happens ?Ī: Already Punched message gives a yellow exclamation point icon. However, to make the usage easier on the employee, insure the clocks are at the same heights with the same distance away from the clock to stand.īasically, customer has to recreate the way they were enrolled to punch. Q: Can you enroll user at one clock and push template to several clocks through software ?Ī: Employees can enroll at one clock and use that template at other clocks without re-enrolling. Q: When SY-910 face recognition clock receives a good punch, is there any indicator displayed on LCD screen to let employee know it was a good punch ?Ī: Yes - it gives a checkmark icon & a cheerful chime sound When enrolling, I recommend putting a spot or something on the ground so people know where to stand. When using more than one, pains should be taken to insure they are all the same level. Face Recognition Help: Q&A Facts: Q: Can you enroll users if unit sitting on table or does it have to be mounted on wall ?Ī: The clock should be mounted. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |